M-audio OmniStudio USB Instrukcja Użytkownika

OMNISTUDIO USBEnglish

A recording console performs two functions. It routes the signal you are about to record, providing the ability to pre-amplify and shape thatsignal be

Inputs and OutputsThe OmniStudio USB provides up to four audio inputs, seen by the host audio application as two stereo pairs, i.e. 1/2 and 3/4. The

There are some basic concepts that apply to all audio gear. Understanding them will help in your operation of the OmniStudio USB, as wellas create a s

Plugs and JacksIn general, a jack is a female connector, and a plug is a male connector. The jack is mounted within the hardware device, and theplug

Line Levels vs. Mic/Instr LevelsMicrophones and guitar pickups typically emit a low signal level, requiring a pre-amp such as those found in the Omn

Windows XPInsert the M-Audio driver CD-ROM into your computer. From the Start menu, select “Run…” then click the Browse button. Browse to the CDdrive

You will then be prompted to reboot your computer. Click “Finish.”After the computer has rebooted, connect the OmniStudio USB to your computer’s USB

Windows 2000Insert the M-Audio driver CD-ROM into your computer. From the Start menu, select “Run…” then click the Browse button. Browse to the CDdriv

Once the installer has finished copying the files, you will be prompted to reboot your computer.After the computer has rebooted, connect the OmniStudi

WindowsMEDo NOT connect the OmniStudio USB to your computer’s USB port at this time. Insert the M-Audio driver CD-ROM into your computer. From the Sta

Table of Contents1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connect the OmniStudio USB to your computer’s USB port. Windows will recognize your new hardware.The New Hardware Wizard will open. Select the default

Windows 98SEDo NOT connect the OmniStudio USB to your computer’s USB port at this time.Insert the M-Audio driver CD-ROM into your computer. Fromthe St

On rebooting, the M-Audio OmniStudio USB Control Panel icon will appear in the system tray. Connect the OmniStudio USB to your computer’s USB port. Wi

Mac OSXInsert the M-Audio driver CD into your CD-ROM drive and open the CD to view its contents. Double click on the OmniStudio USB folder toopen the

When prompted, click "Continue Installation." When prompted, click "Restart" to finish the installation.After the computer has res

Mac OS9Insert the M-Audio driver CD into your CD-ROM drive and open the CD to view its contents. Double click on the OmniStudio USB folder toopen the

Installing and Configuring OMS (MacOS 9 Only)The OmniStudio USB driver CD also contains the program files for OMS (Open Music System), Opcode’s MIDI-m

Along with your driver installation, the OmniStudio USB Control Panel is also installed on your system. On the PC, you’ll find a tiny “M” logolocated

LatencyLatency is defined as the time it takes for your input signal to pass through your audio software and appear at the outputs. Smaller buffersiz

AudioConnect the OmniStudio USB’s Monitor Outputs to your amplifier or powered monitors. You can connect the OmniStudio USB’s Main Outputs to the inpu

14. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MIDIConnect your MIDI device’s MIDI Input to the OmniStudio USB’s MIDI Output. Connect your MIDI device’s MIDI Output to the OmniStudio USB’sMIDI Inpu

the device that is attached to that particular input or output. You can, in fact, have an input set to one line level and the corresponding outputset

As we’ve previously mentioned, the OmniStudio USB offers quite a bit of flexibility in recording and monitoring your audio. In this section wewill ou

Arm the track for recording, and begin recording audio.Once audio is recorded, you can set the output of the tracks you’ve just recorded to outputs 3

If your application supports WDM and direct monitoring, you may enable it in your DAW’s audio control panel. Please refer to youraudio software’s do

Recording External EffectsIn some cases you may wish to record the signal processing along with the audio being recorded, perhaps to free up that de

Next to each Stereo Aux Input is that Input’s Aux Mon/Rec switch. Pressing this switch and engaging it in the IN (Rec) position will routethe audio o

attenuated (reduced). Therefore, the volume level on each individual audio track recorded in your music software will control theplayback level that r

Recording multi-channel audio and MIDI with a computer is a complex process at best, and volumes have been written about it. Setting upyour computer t

Problem: No sound.Possible Cause 1: Drivers have not been correctly installed, or the OmniStudio USB has not been properly configured in your audio so

Thank you for choosing the OmniStudio USB from M-Audio. We designed the OmniStudio USB to be a complete multi-channel recording andplayback solution f

15. Contact Us39M-AUDIO U.S.45 E. Saint Joseph St.Arcadia, CA 91006-2861 U.S.A.Sales Information: 626-445-2842Sales Information (email): info@m-au

Recording/Playback Configurations (USB bandwidth limited)g 16-bit / up to 48 kHz = 4-in, 4-outg 24-bit / up to 48 kHz = 4-in, 2-out OR 2-in, 4-outg 24

Frequency Response:g Mic In to Main Output: +0.0/-0.3dB, 20Hz-20kHzg Instrument In to Main Output: +0.0/-0.3dB, 20Hz-20kHzg Line 3/4 in to Main Output

Minimum System Requirements:Mac Native USB compatibilityG3 or G4 running OS 9.2.2 or later, or OS 10.1.5 or later128 MB RAM (for 96kHz Operation) 64 M

SIGNAL FLOW BLOCK DIAGRAM43

17. Warranty44M-AUDIO warrants this product, under normal use, to be free ofdefects in materials and workmanship for a period of One (1) Yearfrom date

g4-in, 4-out USB audio connectivityg High-resolution, high-performance 24-bit/96kHz A/D and D/A converters with a dynamic range of 103dB on input and

Your OmniStudio USB package contains the following:gOmniStudio USB Recording InterfacegUsers’ ManualgWindows and Mac driver software CDgUSB 1.1 cableg

Front Panel11.. MMiicc//IInnssttrruummeenntt IInnppuuttss 11 aanndd 22– These combo Neutrik connectors will accept a standard three pin XLR low imped

and 4 are monitored as a L/R stereo pair.1133.. DDiirreecctt MMoonniittoorr LLeevveell 44– With Direct Monitor Enable 3 and 4 switch in the IN positi

2255.. UUSSBB CCoonnnneeccttoorr– Connect your computer to the OmniStudio USB here using the included USB cable.2266.. MMIIDDII IInn aanndd OOuutt CC